Synchronous Lifting Lowering and Weighing
Results traceable back to NIST
Computer Controlled Synchronous Lifting and Lowering Systems
- Personal computer based control unit with user-friendly Windows interface
- Digital control of the lifting process accurate to + – .04” [1mm] between leading and lagging lifting points
- Multiple lift point capability, from 2 to 24 points
- Data recording, graphic presentations and print-out capability
- Automatic stop at pre-set stroke or load limit
Setting new standards in precision and control
– Digital control of the lifting process accurate to + – .04” [1mm] between lifting points
– Real time, on screen monitoring provides complete lift status
– Digital control programmed for “Fail-Safe” operation
– Actual load movement is measured
– Pilot-operated check valves automatically hold cylinder pressure in the event of hose failure
– Worldwide network of Enerpac Authorized Service Centers
– Uses easy-to-service, standard Enerpac components
- Ease of Operation
– One person operation
– PC-based controller runs in Windows environment
– Point-and-click mouse control
– Multi-lingual data screens available
– Standard Enerpac 10,000 psi single- and double-acting cylinders
Computer Controlled Synchronous Lifting and Lowering Systems
WB Equipment provides the largest selection of Computer controlled lifting and lowering systems. We have a solution for virtually any application – lifting, pushing, pulling, bending or holding – in most industrial and commercial work environments. We offer hundreds of different configurations of mechanical and hydraulic cylinders and lifting systems, plus products ranging from hydraulic jacks for portability and tight fits, to engineered systems for precise control over multiple lift points.
A jack, screwjack or jackscrew is a mechanical device used as a lifting device to lift heavy loads or to apply great forces. A mechanical jack employs a screw thread for lifting heavy equipment. A hydraulic jack uses hydraulic power. The most common form is a car jack, floor jack or garage jack, which lifts vehicles so that maintenance can be performed. Jacks are usually rated for a maximum lifting capacity (for example, 1.5 tons or 3 tons). Industrial jacks can be rated for many tons of load.
Know What You Want?
A large inventory of Enerpac, Power Team, Simplex, Freyssi Flat Jacks, Skidmore and Calibore equipment enables W.B. to answer any need rapidly and effectively. To discuss the best system for your bridge lowering, raising, or moving, call W. B. Equipment at 866-522-5464 or email email@example.com or firstname.lastname@example.org.
For more information about WB Equipment sales, rentals and service consult our website at https://www.wbequipment.com
WB EQUIPMENT PRODUCTS / SERVICES
- Freyssi Flat Jacks
- Custom Hydraulic Power Units
- Customized Jacking Systems
- Custom Center Hole Cylinders
- Custom Made Hydraulic Jacks
- Hydraulic Jacks
- Hydraulic Presses
- Hydraulic Pumps
- Hydraulic Torque Wrenches
- Hydraulic Jacks And Loadcell Calibration
- Material Handling Equipment
- Mechanical Jacks
- Pallet Trucks
- Pile Testing Equipment
- Pipe Jacking
- Re-Bar Grips
- Railroad Maintenance Equipment
- Strand Jacks
- Stressing Jacks
- Synchronous Lifting Systems
- Tie Back Testing Equipment
PRODUCTS / SERVICES ON THOMASNET.COM
- Construction Equipment
- Calibration Services
- Contractors’ Equipment
- Rebar Grips
- Hydraulic Equipment
- Jacking Services
- Maintenance and Repair Services
- Maintenance Equipment
- Material Handling Equipment
- Mining Equipment
- Pneumatic Systems
OTHER PRODUCTS by WB EQUIPMENT
Custom hydraulic cylinders and hydraulic jacks made to order. Huge inventory readily available. With loads from 1 – 2,000 tons and pressure rating of 100 – I0,000 psi we can make any hydraulic cylinder or hydraulic jack to your exact requirements. Whether it be single acting, double acting, lockout or centerhole let us provide you with the right jacking system to perform your task.
Custom power units and hydraulic pumps made to order. Electric, Gas, Diesel or Air Operated power units. Flow rates range from 1 GPM to 100 GPM. Our hydraulic pumps are available in over 1000 different configurations. They have a pressure rating of 10,000 psi.
Freyssi Flat Jacks are simple, practical devices for the civil or structural engineer wherever the application or control of large forces is required. Flat jacks are frequently used in the solution of unforeseen problems such as in remedial measures or structural additions.
The sensor extension is different from the Cylinder stroke value. The sensor extension is hooked to the load, and it has a value even when the Cylinder is collapsed. The potential applications of this system are numerous synchronized lifting levering, pushing, pulling and positioning using computer technology.of a synchronous lifting system
The hydraulic press depends on Pascal’s principle: the pressure throughout a closed system is constant. One part of the system is a piston acting as a pump, with a modest mechanical force acting on a small cross-sectional area; the other part is a piston with a larger area which generates a correspondingly large mechanical force. Only small-diameter tubing (which more easily resists pressure) is needed if the pump is separated from the press cylinder.
Power Team Monostrand Stressing Jacks are the most durable in the industry.
Monostrand Stressing Jacks suited for work on slab-on-grade where dirt, heat and high volume use take their toll.
Stressing jacks are mainly used on construction sites for stressing mono-strand anchors, and for the separate stressing of the strands of multistrand tendons.
We can provide customized jacking equipment to test driven piles from 1 -2000 tons. The systems can be manually, electrically or automatically controlled.
WB Equipment has delivered components for multiple jacking systems. Our knowledge of structural design, hydraulics, and automation means that we are capable of designing a complete jacking system with controls that allow for fully automated jacking and monitoring.
A hydraulic torque wrenchis a power tool designed to exert torque on a fastener to achieve proper tightening or loosening of a connection through the use of hydraulics. A torque wrench is applied to the nut either directly or in conjunction with an impact socket. Hydraulic torque wrenches apply a predetermined, controlled amount of torque to a properly lubricated fastener.
A strand jack (also known as strandjack) is a jack used to lift very heavy (e.g. thousands tons or more with multiple jacks) loads for construction and engineering purposes.
Strand jacks can be used horizontally for pulling objects and structures, and are widely used in the oil and gas industry for skidded loadouts. Oil rigs of 38000 Te have been moved in this way from the place of construction on to a barge. Since multiple jacks can be operated simultaneously by hydraulic controllers, they can be used in tandem to lift very large loads of thousands of tons. Even the tandem use of two cranes is very difficult operation.
A hoist is a device used for lifting or lowering a load by means of a drum or lift-wheel around which rope or chain wraps. It may be manually operated, electrically or pneumatically driven and may use chain, fiber or wire rope as its lifting medium.
The basic hoist has two important characteristics to define it: Lifting medium and power type. The lifting medium is either wire rope, wrapped around a drum, or load-chain, raised by a pulley with a special profile to engage the chain. The power can be provided by different means. Common means are hydraulics, electrical and air driven motors.
A jack, screwjack or jackscrew is a mechanical device used as a lifting device to lift heavy loads or to apply great forces. A mechanical jack employs a screw thread for lifting heavy equipment.
A hydraulic jack uses hydraulic power. The most common form is a car jack, floor jack or garage jack, which lifts vehicles so that maintenance can be performed. Jacks are usually rated for a maximum lifting capacity (for example, 1.5 tons or 3 tons). Industrial jacks can be rated for many tons of load.
Quick acting re-bar grips are available for pull out testing of reinforcing bars in concrete, (re-bar/reinforcement bars) used in construction of highways, bridges, and tunnels as well as rigging and other applications.
When used with hydraulic jack, user slips jack and grip over grouted re-bar and applies pressure to load. These re-bar grips come in sizes No. 4-18 and accommodate construction industry’s focus on repair, maintenance, and building of public infrastructure.
Custom made cylinders made to your specifications. All cylinders calibrated and traceable back to NIST. Centerhole, locknut, low height, single acting, double acting, long stroke.
- 0-1500 tons
- Centerhole sizes .75 inch to 15 inches
- Stroke ½ inch to 10 feet
Enerpac is a global market leader in high pressure hydraulic tools, controlled force products and solutions for precise positioning of heavy loads.
Work site solutions for stressing, lifting and surfacing for railroad maintenance.
- Track Jacks
- Rail Pullers
- Lifting Jacks
- Truck Jacks